Mettler Toledo M400/2(X)H Specifiche Pagina 83
- Pagina / 111
- Indice
- RISOLUZIONE PROBLEMI
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
Transmitter M400/2(X)H, M400G/2XH 83
© 03 / 2014 Mettler-Toledo AG, CH-8606 Greifensee, Switzerland Transmitter M400/2(X)H, M400G/2XH
Printed in Switzerland 30 031 683
12.3 Model / Software revision
(PATH: Info/Model/Software Revision)
Selecting Model/Software Revision will display the part number, model and the serial number of
the transmitter.
By using the . key it is possible to navigate forward through this menu and get additional infor-
mation like the current version of firmware implemented on the transmitter (Master V_XXXX and
Comm V_XXXX) and – if an ISM sensor is connected – the version of the sensor firmware (Sen-
sor FW V_XXX) and sensor hardware (Sensor HW XXXX).
The displayed information is important for any Service call. Press [ENTER] to exit from this
display.
12.4 ISM sensor info
(available when ISM sensor connected)
(PATH: Info / ISM Sensor Info)
After plugging in an ISM sensor it is possible by using the key A or . to navigate to the Menu
“ISM Sensor Info”.
Press [ENTER] to select the menu.
The following information about the sensor will be shown in this menu. Use up and down
arrows to scroll in the menu. Type: Type of sensor (e.g. InPro 3250)
Cal Date: Date of the last adjustment
Serial-No.: Serial number of the connected sensor
Part-No.: Part number of the connected sensor
Press [ENTER] to exit from this display.
12.5 ISM sensor diagnostics
(available when ISM sensor connected)
(PATH: Info / ISM Diagnostics)
After plugging in an ISM sensor it is possible by using the key A or . to navigate to the Menu
“ISM Diagnostics”.
Press [ENTER] to select the menu.
Navigate to one of the menus, described in this section, and press [ENTER] again.
- Operation Manual 1
- Multi-parameter 1
- 1 Introduction 9
- 2 Safety instructions 10
- 3 Unit overview 14
- 3.2.1 Menu Structure 15
- 3.2.2 Navigation keys 15
- 3.2.6 ”Save changes” dialog 17
- 3.2.7 Security Passwords 17
- 3.2.8 Display 17
- 4 Installation instruction 18
- 4.1.2 Installation procedure 19
- (+ 0,5 mm/– 0,0 mm) 20
- (+ 0.02"/– 0.00") 20
- 4.2.1 Housing (wall mount) 21
- 4.3 Connector PIN denition 22
- 4.3.3 Analog Sensors 23
- InPro 3250i/SG/120 25
- Art.-Nr. 52 005 373 25
- 4.5.2.1 Example 1 27
- 4.5.2.2 Example 2 28
- 4.5.2.3 Example 3 29
- 4.5.2.4 Example 4 30
- 6 Quick Setup 34
- 7 Sensor Calibration 35
- (four electrode sensors only) 37
- 7.2.3 Process Calibration 38
- 7.3.1.1 Auto mode 39
- 7.3.1.2 Manual mode 40
- 7.4 pH calibration 41
- 7.4.1 One point calibration 41
- 7.4.1.1 Auto mode 41
- 7.4.1.2 Manual Mode 42
- 7.4.2 Two-point calibration 42
- 7.4.2.1 Auto Mode 42
- 7.4.2.2 Manual Mode 43
- 7.4.3 Process calibration 44
- (only for analog sensors) 46
- (only for analog sensor) 47
- 7.7 Sensor verication 47
- 8 Conguration 48
- 8.2.1.1 Analog sensor 49
- 8.2.1.2 ISM sensor 49
- 8.2.3.2 Concentration table 52
- 8.2.3.3 pH / ORP parameters 53
- or . key 54
- 8.2.4 Set averaging 55
- 8.3 Analog outputs 56
- 8.4 Set points 57
- 8.5 Alarm / Clean 58
- 8.5.1 Alarm 58
- 8.5.2 Clean 59
- 8.6 ISM set up 60
- 8.6.1 Sensor monitoring 60
- 8.6.2 CIP Cycle Limit 61
- 8.6.3 SIP Cycle Limit 62
- and . keys and press 63
- 8.7 Display 64
- 8.7.1 Measurement 64
- 8.7.2 Resolution 65
- 8.7.3 Backlight 65
- 8.7.4 Name 65
- 8.8 Hold analog outputs 66
- 9 System 67
- 9.2.1 Changing passwords 68
- 9.3 Set / Clear lockout 68
- 9.4 Reset 68
- 9.4.1 Reset system 69
- 9.5 Set date & time 69
- 10 PID setup 70
- 10.1 Enter PID setup 71
- 10.2 PID auto / manual 71
- 10.3 Mode 71
- 10.3.1 PID mode 72
- 10.4 Tune parameters 73
- 10.4.3 Proportional limits 73
- 10.4.4 Corner points 73
- 10.5 PID display 74
- 11 Service 75
- 11.1.3 Display 76
- 11.1.4 Keypad 76
- 11.1.5 Memory 76
- 11.1.6 Set OC 76
- 11.1.7 Read OC 77
- 11.1.8 Set analog outputs 77
- 11.1.9 Read analog outputs 77
- 11.2 Calibrate 77
- 11.2.1.1 Temperature 78
- 11.2.1.2 Current 78
- 11.2.1.3 Voltage 79
- 11.2.1.4 Rg diagnostic 79
- 11.2.1.5 Rr diagnostic 80
- 11.2.2 Calibrate unlock 81
- 11.3 Tech Service 81
- 12 Info 82
- 12.4 ISM sensor info 83
- 13 Maintenance 86
- 14 Troubleshooting 87
- 14.3.3 ORP messages 89
- 14.4 Amperometric O 90
- Error messages / 90
- Warning- and Alarm list 90
- 14.4.3 Trace oxygen sensors 91
- 14.5.1 Warning indication 92
- 14.5.2 Alarm indication 92
- 16 Specications 94
- 17 Default table 99
- Resistivity/Conductivity 103
- 18 Warranty 104
- 19 Buffer tables 105
- 19.1.2 Mettler-10 106
- 19.1.5 Hach buffers 107
- 19.1.6 Ciba (94) buffers 108
- 19.1.8 WTW buffers 109
- 19.1.9 JIS Z 8802 buffers 109
Prodotti e manuali riguardandi Misurazione, test & controllo Mettler Toledo M400/2(X)H
(131 pagine)
(2 pagine)Groupe SEB USA - T-FAL Monitores del bebé manuales de usuario
La lista de productos de Groupe SEB USA - T-FAL Monitores del bebé contiene 2 manuales de usuario para 2 seleccionados. Todas las guías de usuario en pdf están disponibles para descargar o ver en línea.
Commenti su questo manuale